Professional RC Hobby Drone Store, Keep on Updating……

QWiNOut S600 4-Axle DIY Drone Kit Aerial Photography Aircraft PNP 600mm Frame Kit with Landing Gear Skid + APM2.8 Flight Control + 30A ESC + 930KV Motor + 1045 Paddles


Regular price $177.11

Shipping calculated at checkout.
QWiNOut S600 4-Axle DIY Drone Kit Aerial Photography Aircraft PNP 600mm Frame Kit with Landing Gear Skid + APM2.8 Flight Control + 30A ESC + 930KV Motor + 1045 Paddles

DIY Drone kit and unassembled, comes with high quality electronic accessories;
ESCs and Motors was soldered with 3.5mm banana connectors, Effectively avoid welding problems;
Only need to add a 2-3S Lipo battery and 6CH above radio system to complete assemble and fly;
Have Set Up The ESC Program, Do Not Need Additional Program;
Colored Paddles for orientation to keep you flying in the right direction.

Package listing:
1* S600 Super Hard Arm 4-Axis Rack Quadcopter Frame Kit with Landing Gear Skid
2* Pairs of 1045 CW+CCW Propellers (Black)
1* Pairs of 1045 CW+CCW Propellers (Red)
6* A2212 930KV Brushless Motor 15T
6* 30A Brushless ESC Speed Controller
1* APM 2.8 Multicopter Flight Controller Board with Extension Cable- Straight pin
1* GPS7M with Compass
1* GPS folding antenna Mount

Brand: QWinOut
Wheelbase: 600mm
Flight Control: APM 2.8 Multicopter Flight Controller Board with Extension Cable- Straight pin
Motor: A2212 930KV Brushless Motor 15T
ESC: 2-4S 30A Brushless ESC Simonk Firmware with 5V 3A BEC
Paddle: 1045 2-blade Plasic
Loading weight: Up to 1KG under 3S battery (Battery Not included)

Wheelbase: 600mm
Tripod height: 250mm
Maximum available paddle: 15 inch
Weight: 860g
Upper and lower center plate middle height: 36mm

Flight Controller: 
APM 2.8 Multicopter Flight Controller Board
- Compatible for Arduino!
- Includes 3-axis Gyro, Accelerometer and Magnetometer, Along with a High-performance Barometer
- On Board 4 Mega Byte Dataflash Chip for Automatic Datalogging
- Optional Off-board GPS
- One of the First Open Source Autopilot Systems to Use Invensense's 6 DOF Accelerometer/Gyro MPU-6000.
- Barometric Pressure Sensor Upgraded to MS5611-01BA03, from Measurement Specialties.
- Atmel's ATMEGA2560 and ATMEGA32U-2 Chips for Processing and USB Functions Respectively.


7M refresh rate increased to 10Hz, 6M and 6H are 5Hz, search star speed, cold start speed than 6M, 6H twice as fast. Positioning accuracy of 2.5M, built-in high-precision electronic compass.
Due to the ultra-high performance of this product multi-GNSS (GPS, GLONASS, Galileo, QZSS and SBAS) engines, it provides high sensitivity positioning in the shortest acquisition time.

56-channel compatible with u-blox 7 engine
Hardware support Galileo E1B / C, Compass
The maximum update rate is 10 Hz
Accuracy GPS / GLONASS
Positioning 2.5 m CEP / 4.0 m
SBAS 2.0 m CEP / n.a.
Cold start: 29 s / 30 s
Auxiliary start: 5 s / n.a.
Re-capture: 1 s / 3 s
Sensitivity GPS / GLONASS
Tracking: -162 dBm / -158 dBm
Cold start: -148 dBm / -140 dBm
Temperature start: -148 dBm / -145 dBm

KV: 930rpm/V
Min Current:  4A
Max Current 10A
Max Efficiency: 80%
No. Of Cells: 2-3 Li-Poly
Motor Dimensions: 27.5x30mm
Shaft Diameter: 3.17mm

Working current: 30A
Output: Continuous 25A, Burst 40A up to 10 Secs
Input Voltage:2-4 cells lithium battery or 5-12 cells NiCd/NIMh battery
Max Speed: 210,000rpm for 2 Poles BLM, 70,000rpm for 6 poles BLM,35,000rpm for 12 poles BLM.(BLM: BrushLess Motor)
1.Safety Arming Feature: Regardless the throttle stick position, the motor will not spin after battery connected.
2.Throttle Calibration: Throttle range can be configured to provide best throttle linearity, fully compatible with all market available transmitters.
3.Programmable Items:Brake Setting:brake enabled/brake disabled. Battery Type:Li-xx(Li-ion or LiPo)/Ni-xx(NiMh or NiCd). Low Voltage Protection Mode(Cutoff Mode):Gradually reduce the output power/Cutoff the output power. Low Voltage Cutoff Protection Threshold (Cutoff Threshold):low/medium/high. Start Mode: normal/soft/very soft. Timing:low/medium/high. Reset: reset all the programmable items to their default settings.
4.Full Protection Features: Low voltage cutoff protection/Over-heat protection/Throttle signal lost protection.

1. Do not modify any parameters and wiring without knowing the flight control and remote control.
2. The product is already welded, you only need to assemble it, and bind the receiver with transmitter, then could fly.
3. Do not charge the battery when you are not at home. Do not charge the battery immediately after flying. Do not over-discharge the battery. (Over-discharge may cause the battery to be charged and become obsolete.) If the battery is fully charged, it may not be charged for a long time.
4. Turn on the remote control before powering the aircraft. After the flight is over, unplug the power supply and turn off the remote control to prevent accidents.
5. You can fly it on open space when there is no wind, do not fly in the crowd and surrounding areas with interference.
6. The product is unassembled. Please watch the teching video before you assemble it, we have the instructions, which would come with the products, and we have a professional dedicated technical team to help solve the relevant questions.
7. If the customer needs to assemble, we will give a reasonable quotation for additional logistics freight and technical assembly fees.
8. This product is not a toy and is not suitable for children under 14 years old.
9. If you are a beginner, it is recommended to be assisted by experienced adults.
10. Novices should pay attention to the fact that when the plane is turning, do not take the plane with your hand or let the child take it to prevent it from being scratched.
11. When the aircraft falls into the wall or hit other objects at high altitude, please close the start switch in time. Otherwise, it may cause damage to the flight control motor. Check the aircraft for damage. If the screw is loose, wait until everything is normal before you can take off again.