Radiolink PIX 32 Bit 4G Flight Controller & M8N GPS Combo Set for AT9/AT10 Remote Controller OSD DIY RC Multicopter Drone
Radiolink PIX 32 Bit 4G Flight Controller & M8N GPS Combo Set with Switch / Power Module / Buzzer / 8G TF Card / GPS Stand Holder for AT9/AT10 Remote Controller OSD DIY RC Multicopter Drone
Open source products, once sold, no return, if quality problems, Please return for repair . Does not provide one to one support. Buy carefully!
1x Radiolink PIX Flight Controller
1x M8N GPS Module
1x GPS Stand Holder
1x Power Module
1x Safe Switch
1x 4G Memory Card
1x Dupont Cable
1. Top Configuration
1) GPS decoder chip: Radiolink M8N GPS, with u-blox UBX-M8030(M8), 72-channel, MMIC BGA715L7 from Infineon and 13 years of RF experiences, is much better than single GNSS 7N.
A.Concurrent reception of GPS/QZSS L1 C/A,GLONASS L10F, BeiDou B1
B.SBASL1 C/A:WAAS, EGNOS, MSAS
2) Antenna : 2.5dbI high gain and selectivity ceramic antenna
3) Power amplify IC: MMIC BGA715L7 from Infineon
4) Filter: SAWF(Surface acoustic wave filter) form Murata
5) Geomagnetic: HMC5983 from Honeywell
2. Professional Design
Radiolink M8N GPS, benefits from professional wireless experiences of Radiolink engineers, exceed the limitation of IC sensitivity index from circuit schematic design to PCB placement.1 meter position accuracy, positioning in 23 seconds and valley stationkeeping ability make Radiolink GPS much better than the similar products.
3. High Performance Cost Ratio
Reasonable price with better hardware, software configuration and brand new exterior designs.
1) Positional Accuracy: 1m precision when working with concurrent GNSS, 2.5m precision when working with single GNSS.
2) Velocity precision: 0.1m/s
3) Max height: 50000m
4) Max speed: 515m/s
5) Max acceleration: 4G
6) Max update rate: up to 18Hz
Tracking & Nav.: -167dBm; Reacquisition:-163dBm; Cold start:-151dBm; Hot start:-159dBm.
8) Time to first fix: Cold start: 26s, Hot start:1s.
9) Connect ports
Power supply: voltage 3.3VDC+-5%, current 50~55mA
A.GPS UART interface, baud rate: 1.2K/4.8K/9.6K/19.2K/38.4K/57.6K/112.5K
B.Geomagnetic I2C interface
- AT9/AT10 Remote Controller Multirotor Menu Setting,specifically customized to PIX Flight attitude parameter setting, correspondence, beginners can easily set
(Note, Product do not include the remote controller and OSD, Please ready by yourself)
- Customization, comprehensive technical support, at hand and fly, erfectly embodies PIX function and fun flight
- 3DR same original, the new circuit design, reduce the interfere in flight control internal board original board , achieve less noise, more accurate compass (route more accurate, more stable point), safer and quieter.
32bit STM32F427 ARM Cortex M4 Core + FPU (floating point unit)
168 MHZ / 256 KB RAM / 2 MB RAM
32bit STM32F103 Fault Protection Coprocessor
Invensense MPU6000 3-axle Accelerometer / Gyroscope
STcro LSM303D 14Bit Accelerometer / Magnetometer
MS5611 MEAS barometer
Micro L3GD20 16 Bit gyroscope
- All interfaces fully tested and accurately detectd by automatic detection system software , avoid bad interfaces lead to flight control installation unsuccessfully.
Multiple flight mode switch freely, Helicopters, Fixed-wing, Multi-rotor,Model Car,Arbitrary;
Multiple flight mode, support for self-stability, high-set, fixed, hover, drift, sports, stunt, circling, following, return, landing, guidance, automatic, all-powerful!
1x SPKT/DSM Receiver interface
2x OSD/Radio Telemetry interface
1x SPI Bus
1x Power Module interface
1x Safe Switch
1x Serial 4/5
1x GPS Module
1x Cam (Controller Area Network) Bus
1x 12C Interface
1X LED Light