HappyModel Mobula6 2024 V3 1S 65mm ultra light micro FPV BWhoop For SE0702 KV28000 brushless motor FPV Tinywhoop Drone

Flight controller

CrazybeeG473

SuperX ELRS V2.0

Firmware target

Betaflight 4.6 CrazybeeG473

Customized STM32F411

Built-in ExpressLRS receiver

Serial ELRS 2.4GHz

Serial ELRS 2.4GHz

Built-in Dshot ESC

5A

5A

Receiver antenna plug

Enameled Copper wire

Enameled Copper wire

Onboard VTX power

25mw~400mw

25mw~400mw

Brushless Motor

0702 KV28000 no plug

0702 KV28000 with plug

Propeller

Gemfan 1208-3 tri-blade

Gemfan 1208-3 tri-blade

Battery plug

A30(compatible with BT2.0)

A30(compatible with BT2.0)

Frame

Mobula6 2024 frame 2.76gram

Mobula6 2024 frame 2.76gram

Mobula6 2024 1S 65mm whoop Drone Frame +Canopy

1

CrazybeeG473 AIO 5-IN-1 Flight controller

1

SE0702 KV28000 brushless motor

4

Gemfan 1208-3 31mm tri-blade propellers(4cw+4ccw)

1

HQPROP ultralight whoop prop 1.2x1.1x3(2cw+2ccw)

1

Nano5 1200TVL camera NTSC 4:3

1

Onboard 5.8G 25mw~400mw VTX

1

Spare canopy

1

Propeller disassemble tool

1

Screw driver

1

Propellers

Materials: PC

Inch: 31mm   

Pitch: 0.8 in 

Weight: 0.21g    

Mount hole diameter:  1mm

Flight controller

MCU: STM32G473CEU6

Gyro: ICM42688P

Sensor: Voltage & Current

BEC: 5V, Max. 2A

UART: UART 1, UART 2, UART 3 (For RX), UART 4(For VTX)

BetaFlight OSD: AT7456E

ESC: 5A continuous

RX: Serial ELRS 2.4GHz

RX antenna: Enameled copper wire 31mm length

Receiver firmware target: HappyModel EP1/EP2 2.4GHz RX

OPENVTX: 5.8GHz 48 channels, Max. 400mW

FC firmware target: CRAZYBEEG473

USB port: SH1.0-4Pin

Battery connector: A30

Mounting hole size: 25.5mm x 25.5mm

Weight: 3.83g without pigtail and vtx antenna

Onboard 4in1 ESC

Power supply: 1S LiPo/LiPo HV

Current: 5A continuous peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: Bluejay v0.21

Firmware target: A_X_5_96KHz
Default protocol: DSHOT300 DSHOT600

Recommend ESC Startup power value to min1100/max1200

Onboard Serial ExpressLRS receiver

Packet Rate option: 50Hz/150Hz/250Hz/500Hz

ExpressLRS Firmware version: V3.0
RF Frequency: 2.4GHz

Antenna : Enameled copper wire antenna
Telemetry output Power: <12dBm

Receiver protocol: Serial_based CRSF

Compatible with ExpressLRS V3.x.x TX Module

Could flash single ELRS receiver firmware by Wifi

ExpressLRS firmware target: Generic ESP32 2.4Ghz Rx and VTx

Onboard 5.8g VTX

OPENVTX Firmware

Support firmware upgrade by openvtx configurator

Output power: PIT/10/25/100/400

Frequency: 5.8GHz 48 channels, with Raceband: 5658~5917MHz

Channel SEL: SmartAudio2.1

Modulation type: FM

Operating temperature: -10℃~+80℃

Antenna port: IPEX1/U.FL

Nano5 Camera

Image Sensor: 1/3" CMOS

Horizontal Resolution: 1200 TVL

Lens: 2.1mm (M10) 155° FOV

TV System: NTSC

Signal-to-Noise Ratio: >52dB

Electronic Shutter: Auto

Automatic Gain Control (AGC): Auto

Minimum Illumination: 0.001Lux@1.2F

Digital Wide Dynamic Range: Auto

Power Supply: DC 3-5.5V

Current: 110mA@5V 120mA@3.3V

House Material: ABS

Net Weight: 1.57g (1.0mm plug version)